beroNet berofix card series is a powerful and flexible hardware solution to connect BRI ISDN, PRI ISDN, and GSM lines to any SIP based VoIP system. Due to the special design of the hardware berofix will be detected as a standard Network card by the operating system. Usually the driver for this network card will be loaded automatically by the OS. The beroNet berofix card series consist of a baseboard and the so called Line interfaces. Each berofix baseboard can carry up to 2 berofix Lineinterface modules.

Due to the modular concept you can mix BRI ISDN, PRI ISDN, and GSM ports on one card with full below described features which makes the berofix cards very unique. The berofix cards support the following hardware DSP based Voice-Processing features:

• G.168/G.165 Echo cancellation with echo path change detection, up to 128ms
• Codec translation: G.723.1 and Annex A, G.729a, G.726, G.711u/a
• DTMF detection and generation
• T.38 fax relay (V.27,V.29 and V.17)
• SIP over TCP with SRTP and TLS (available Q1 2010)
• Hardware Conferencing (available Q1 2010)
• DSS1, EuroISDN conform (features set: COLP,CFU/CFB,CFNRY ...) (available Q1 2010)
• Q.SIG Basic-Features set: CNIP,CNIR,CONP (available Q1 2010)
• PCM Bus interconnection between berofix cards to enable hardware bridging for transparent voice, data and Fax transmission via optional PCM-Bus cable. (available Q1 2010)

Additional Information/Documentation

• Product Datasheet

Manufacturer's Product Warranty Period: 2-years.

Availability: Immediate/In-Stock.

beroNet berofix card series is a powerful and flexible hardware solution to connect BRI ISDN, PRI ISDN, and GSM lines to any SIP based VoIP system. Due to the special design of the hardware berofix will be detected as a standard Network card by the operating system. Usually the driver for this network card will be loaded automatically by the OS. The beroNet berofix card series consist of a baseboard and the so called Line interfaces. Each berofix baseboard can carry up to 2 berofix Lineinterface modules.

Due to the modular concept you can mix BRI ISDN, PRI ISDN, and GSM ports on one card with full below described features which makes the berofix cards very unique. The berofix cards support the following hardware DSP based Voice-Processing features:

• G.168/G.165 Echo cancellation with echo path change detection, up to 128ms
• Codec translation: G.723.1 and Annex A, G.729a, G.726, G.711u/a
• DTMF detection and generation
• T.38 fax relay (V.27,V.29 and V.17)
• SIP over TCP with SRTP and TLS (available Q1 2010)
• Hardware Conferencing (available Q1 2010)
• DSS1, EuroISDN conform (features set: COLP,CFU/CFB,CFNRY ...) (available Q1 2010)
• Q.SIG Basic-Features set: CNIP,CNIR,CONP (available Q1 2010)
• PCM Bus interconnection between berofix cards to enable hardware bridging for transparent voice, data and Fax transmission via optional PCM-Bus cable. (available Q1 2010)

Additional Information/Documentation

• Product Datasheet

Manufacturer's Product Warranty Period: 2-years.

Availability: Immediate/In-Stock.

beroNet berofix card series is a powerful and flexible hardware solution to connect BRI ISDN, PRI ISDN, and GSM lines to any SIP based VoIP system. Due to the special design of the hardware berofix will be detected as a standard Network card by the operating system. Usually the driver for this network card will be loaded automatically by the OS. The beroNet berofix card series consist of a baseboard and the so called Line interfaces. Each berofix baseboard can carry up to 2 berofix Lineinterface modules.

Due to the modular concept you can mix BRI ISDN, PRI ISDN, and GSM ports on one card with full below described features which makes the berofix cards very unique. The berofix cards support the following hardware DSP based Voice-Processing features:

• G.168/G.165 Echo cancellation with echo path change detection, up to 128ms
• Codec translation: G.723.1 and Annex A, G.729a, G.726, G.711u/a
• DTMF detection and generation
• T.38 fax relay (V.27,V.29 and V.17)
• SIP over TCP with SRTP and TLS (available Q1 2010)
• Hardware Conferencing (available Q1 2010)
• DSS1, EuroISDN conform (features set: COLP,CFU/CFB,CFNRY ...) (available Q1 2010)
• Q.SIG Basic-Features set: CNIP,CNIR,CONP (available Q1 2010)
• PCM Bus interconnection between berofix cards to enable hardware bridging for transparent voice, data and Fax transmission via optional PCM-Bus cable. (available Q1 2010)

Additional Information/Documentation

• Product Datasheet

Manufacturer's Product Warranty Period: 2-years.

Availability: Immediate/In-Stock.

beroNet berofix BF4S0 is a BRI ISDN Lineinterface module for the berofix card series.The beroNet BF4S0 Lineinterface module can be configured individually for each port to NT (Network Termination) or TE (Terminal Equipment) mode. In either modes the module supports Point-To-Multi-Point (PMP) or Point-To-Point (PTP). The TE/NT mode as well as the Line termination of 100 ohms are selectable via software (Jumper-free).

Features

• 4 BRI ports
• Each port can be configured individually for TE / NT mode
• Line termination (100 Ohms) for each port
• TE/NT as well as the line termination is selectable via software (Jumper-free)
• All ISDN ports are short-circuit protected (by electronic fuse, auto-reset)
• Hardware bridging (for transparent voice, data and fax transmission)

Additional Information/Documentation

• Product Datasheet

Manufacturer's Product Warranty Period: 2-years.

Availability: Immediate/In-Stock.

beroNet berofix BF1E1 is a PRI ISDN Lineinterface module for the berofix card series. The beroNet BF1E1 Lineinterface module can be configured individually for each port to NT (Network Termination) or TE (Terminal Equipment) mode. The default Pin-Out of this module is always TE mode with PINS 1,2,4,5. If you want to use NT-mode you may need a cross-cable which is optionally available (BNE1Crosscable). Line termination (120/75 Ohms) is selectable for each port by DIP switches on the Lineinterface module.

Features

• 1 PRI port
• Each port can be configured individually for TE / NT mode
• Line termination selectable via DIP Switches
• Hardware bridging (for transparent voice, data and fax transmission)

Additional Information/Documentation

• Product Datasheet

Manufacturer's Product Warranty Period: 2-years.

Availability: Immediate/In-Stock.

beroNet berofix BF2E1 is a PRI ISDN Lineinterface module for the berofix card series. The beroNet BF2E1 Lineinterface module can be configured individually for each port to NT (Network Termination) or TE (Terminal Equipment) mode. The default Pin-Out of this module is always TE mode with PINS 1,2,4,5. If you want to use NT-mode you may need a cross-cable which is optionally available (BNE1Crosscable). Line termination (120/75 Ohms) is selectable for each port by DIP switches on the Lineinterface module.

Features

• 2 PRI ports
• Each port can be configured individually for TE / NT mode
• Line termination selectable via DIP Switches
• Hardware bridging (for transparent voice, data and fax transmission)

Additional Information/Documentation

• Product Datasheet

Manufacturer's Product Warranty Period: 2-years.

Availability: Immediate/In-Stock.